Zebra

Zebra QL420 Plus: Adjusting the Power Inactivity Timeout

by ScanSource Technical Services October 15, 2011 Barcode Printing
Thumbnail image for Zebra QL420 Plus: Adjusting the Power Inactivity Timeout

All QL’s come with a default power.inactivity_timeout set to 1200 seconds. (20 minutes). We will adjust it to 0 to keep it from going into sleep mode. However, if you want it set to a different amount of time simply adjust the number in the power.inactivity_timeout.txt file to the desired number of seconds and continue [...]

Read More

Zebra R110Xi4: How to Reset Printer to Factory Defaults

by ScanSource Technical Services July 26, 2011 Barcode Printing
Thumbnail image for Zebra R110Xi4: How to Reset Printer to Factory Defaults

To reset defaults through the front panel, Press two times. The LCD will read SAVE CHANGES. Press until LOAD DEFAULTS is displayed. Press again. The printer will then display LOADING DEFAULTS. Once the printer has reset to default it will perform a self calibration. Still have questions or technical trouble? If your already a ScanSource [...]

Read More

Zebra Setup Utility: How to Setup Wireless Printer Communication

by ScanSource Technical Services July 26, 2011 Barcode Printing
Thumbnail image for Zebra Setup Utility: How to Setup Wireless Printer Communication

Load the Zebra Setup Utility that came on the CD with your printer or download it if needed. When you open Zebra Setup Utility, you will need to load the ZDesigner driver and interface for your corresponding printer. You will now need to highlight your printer and click on “Configure Printer Connectivity”. You will now [...]

Read More

Zebra QL220 Plus: Fixing the Light Print Issue

by ScanSource Technical Services July 22, 2011 Barcode Printing
Thumbnail image for Zebra QL220 Plus: Fixing the Light Print Issue

Follow these Instructions in order. Install the BigFoot application. After you install BigFoot connect up the QL to your computer. If you get the found new hardware wizard, just click cancel on this and close it out. Run the BigFoot Application. In the top left corner click AllCv and it will populate. This will verify [...]

Read More

Zebra QL320 Plus: Fixing the Light Print Issue

by ScanSource Technical Services July 22, 2011 Barcode Printing
Thumbnail image for Zebra QL320 Plus: Fixing the Light Print Issue

Follow these Instructions in order. Install the BigFoot application. After you install BigFoot connect up the QL to your computer. If you get the found new hardware wizard, just click cancel on this and close it out. Run the BigFoot Application. In the top left corner click AllCv and it will populate. This will verify [...]

Read More

Zebra QL420 Plus: Fixing the Light Print Issue

by ScanSource Technical Services July 22, 2011 Barcode Printing
Thumbnail image for Zebra QL420 Plus: Fixing the Light Print Issue

Follow these Instructions in order. Install the BigFoot application. After you install BigFoot connect up the QL to your computer. If you get the found new hardware wizard, just click cancel on this and close it out. Run the BigFoot Application. In the top left corner click AllCv and it will populate. This will verify [...]

Read More

Zebra Setup Utility: How to Reset Printer to Factory Defaults

by ScanSource Technical Services June 29, 2011 Barcode Printing
Thumbnail image for Zebra Setup Utility: How to Reset Printer to Factory Defaults

Download and install Zebra Setup Utility or install if from the CD that came with your printer. When you open Zebra Setup Utility, you will need to load the ZDesigner driver and interface for your corresponding printer. You will now need to highlight your printer and click on “Open Printer Tools”. You will now need [...]

Read More

Zebra 110XiIII Plus: How to Reset Printer to Factory Defaults

by ScanSource Technical Services June 26, 2011 Barcode Printing
Thumbnail image for Zebra 110XiIII Plus: How to Reset Printer to Factory Defaults

To reset defaults through the front panel, Press two times. The LCD will read SAVE CHANGES. Press until LOAD DEFAULTS is displayed. Press again. The printer will then display LOADING DEFAULTS. Once the printer has reset to default it will perform a self calibration. Still have questions or technical trouble? If your already a ScanSource [...]

Read More

Zebra Setup Utility: How to Change Print Mode

by ScanSource Technical Services June 26, 2011 Barcode Printing
Thumbnail image for Zebra Setup Utility: How to Change Print Mode

Install and open the Zebra Setup Utility. It can be found on the CD that ships with the printer or downloaded from the link above.   Open the utility and select the correct ZDesigner driver and interface for your corresponding printer. Once the driver is installed, highlight your printer and click on Configure Printer Settings. [...]

Read More

Zebra S4M: How Can I See the Total Number of Inches the Printhead has Printed?

by ScanSource Technical Services June 26, 2011 POS
Thumbnail image for Zebra S4M: How Can I See the Total Number of Inches the Printhead has Printed?

Once printer is in ready mode. Press the menu key. Press left arrow until you see “ADVANCED SETUP 3″. Press the enter button. It will now ask for the password. The password is “9999″. The horizontal arrows move the cursor to the left and right. The vertical arrows increment the choice the cursor is on. [...]

Read More

← Previous Entries