Replacement

Datamax-O’Neil Mark III: How to Replace the Printhead

by ScanSource Technical Services August 1, 2011 Barcode Printing
Thumbnail image for Datamax-O’Neil Mark III:  How to Replace the Printhead

If the Printhead becomes damaged or worn, replace it as follows: Turn OFF the printer and remove the ribbon if installed. Lower the Ribbon Handler Assembly. Press outward on the two Printhead Carrier Tabs and rotate the Printhead Carrier down. Press inward on the two Printhead Shield Tabs and rotate the Printhead Shield down. Loosen […]

Printronix T4M: How to Replace the Printhead

by ScanSource Technical Services January 29, 2011 Barcode Printing
Thumbnail image for Printronix T4M: How to Replace the Printhead

Replacing the Printhead on a T4M/SL4M WARNING: Always unplug the printer power cord from the printer or power outlet before doing any installation procedure. Failure to remove power could result in injury to you and damage the equipment. When applicable, you will be instructed to apply power.   Set the printer power switch to O […]

Sato GT412e: How to Replace the Printhead

by ScanSource Technical Services January 18, 2011 Barcode Printing
Thumbnail image for Sato GT412e: How to Replace the Printhead

Sato GT412e Printhead Replacement Switch off the printer and disconnect the power supply cord. Open the top housing cover. Press printhead release lever (1, Figure 1-1a) to the right. Carefully lower and withdraw defective printhead (2) from print assembly (3). Disconnect the two wiring harnesses from defective printhead (2). Connect the two wiring harnesses to […]

Printronix T5000: How To Replace the Printhead

by ScanSource Technical Services November 18, 2010 Barcode Printing
Thumbnail image for Printronix T5000: How To Replace the Printhead

Replacing the Printhead Printronix T5000 WARNING: Always unplug the printer power cord from the printer or power outlet before doing any installation procedure. Failure to remove power could result in injury to you and damage the equipment. When applicable, you will be instructed to apply power.   Set the printer power switch to O (Off). […]

Printronix SL4M: How to Replace the Printhead

by ScanSource Technical Services November 18, 2010 Barcode Printing
Thumbnail image for Printronix SL4M: How to Replace the Printhead

Replacing the Printhead on a SL4M WARNING: Always unplug the printer power cord from the printer or power outlet before doing any installation procedure. Failure to remove power could result in injury to you and damage the equipment. When applicable, you will be instructed to apply power. Set the printer power switch to O (Off). […]

Sato M8400RV: How to Replace the Platen Roller

by ScanSource Technical Services November 15, 2010 Barcode Printing
Thumbnail image for Sato M8400RV:  How to Replace the Platen Roller

Switch the printer OFF and disconnect the power cable. Open the top and side access doors on the mechanical side of the printer. Loosen (2) inside screws holding the LH cover to the inside top of the printer and remove (1) screw holding the cover to the frame. Lift the cover for access to the […]

Sato M10e: How to Replace the Platen Roller

by ScanSource Technical Services November 10, 2010 Barcode Printing
Thumbnail image for Sato M10e:  How to Replace the Platen Roller

Switch off the printer and disconnect the power supply cord. Remove the top, front, and right housing covers. Remove timing belt (1, Figure 1-1) from the right end of platen roller (2). Loosen/remove screws (3) securing clamps (4) to printer frame (5) on each end of roller (2). Lift away clamps (4). Manipulate platen roller […]

Sato M10e: How to Replace a Printhead

by ScanSource Technical Services November 10, 2010 Barcode Printing
Thumbnail image for Sato M10e:  How to Replace a Printhead

Switch off the printer and disconnect the power supply cord. Open the top housing cover and remove ribbon stock as applicable. Remove center post screw (1, Figure 1-1) securing printhead (2) to print assembly (3). Disconnect wiring harnesses (A) and (B) from printhead (2). Lift away printhead (2). Orient replacement print head (2) with its […]

Sato GT412e: How to Replace the Platen Roller

by ScanSource Technical Services November 10, 2010 Barcode Printing
Thumbnail image for Sato GT412e: How to Replace the Platen Roller

Sato GT412e Platen Roller Replacement Switch off the printer and disconnect the power supply cord. Remove the side cover and lower front housing cover. Remove one screw (1, Figure 1-1) securing platen roller assembly (2) to printer frame (3). Withdraw worn platen roller assembly (2) from within the printer and insert its replacement. Secure replacement […]

Sato GT408e: How to Replace the Platen Roller

by ScanSource Technical Services November 10, 2010 Barcode Printing
Thumbnail image for Sato GT408e: How to Replace the Platen Roller

Sato GT408e Platen Roller Replacement Switch off the printer and disconnect the power supply cord. Remove the side cover and lower front housing cover. Remove one screw (1, Figure 1-1) securing platen roller assembly (2) to printer frame (3). Withdraw worn platen roller assembly (2) from within the printer and insert its replacement. Secure replacement […]