Printhead

Printronix T5000: How To Replace the Printhead

by ScanSource Technical Services November 18, 2010 Barcode Printing
Thumbnail image for Printronix T5000: How To Replace the Printhead

Replacing the Printhead Printronix T5000 WARNING: Always unplug the printer power cord from the printer or power outlet before doing any installation procedure. Failure to remove power could result in injury to you and damage the equipment. When applicable, you will be instructed to apply power.   Set the printer power switch to O (Off). […]

Printronix T4M: How to Do a Printhead Alignment

by ScanSource Technical Services November 18, 2010 Barcode Printing
Thumbnail image for Printronix T4M: How to Do a Printhead Alignment

Printhead Alignment T4M Align the printhead under the following conditions: to improve the print quality when running difficult media with major differences in thickness, when adjusting for media thickness (with the printhead pressure switch) did not yield adequate print quality, or when you replace the printhead. The printhead must be parallel with the platen for […]

Printronix SL4M: How to Replace the Printhead

by ScanSource Technical Services November 18, 2010 Barcode Printing
Thumbnail image for Printronix SL4M: How to Replace the Printhead

Replacing the Printhead on a SL4M WARNING: Always unplug the printer power cord from the printer or power outlet before doing any installation procedure. Failure to remove power could result in injury to you and damage the equipment. When applicable, you will be instructed to apply power. Set the printer power switch to O (Off). […]

Sato M10e: How to Replace a Printhead

by ScanSource Technical Services November 10, 2010 Barcode Printing
Thumbnail image for Sato M10e:  How to Replace a Printhead

Switch off the printer and disconnect the power supply cord. Open the top housing cover and remove ribbon stock as applicable. Remove center post screw (1, Figure 1-1) securing printhead (2) to print assembly (3). Disconnect wiring harnesses (A) and (B) from printhead (2). Lift away printhead (2). Orient replacement print head (2) with its […]

Sato GT408e: How to Replace the Printhead

by ScanSource Technical Services November 10, 2010 Barcode Printing

Sato GT408e Printhead Replacement Switch off the printer and disconnect the power supply cord. Open the top housing cover. Press printhead release lever (1, Figure 1-1a) to the right. Carefully lower and withdraw defective printhead (2) from print assembly (3). Disconnect the two wiring harnesses from defective printhead (2). Connect the two wiring harnesses to […]

Sato M5900RV: How to Replace the Printhead

by ScanSource Technical Services November 10, 2010 Barcode Printing
Thumbnail image for Sato M5900RV: How to Replace the Printhead

Sato M5900RV Printhead Replacement Turn OFF the Power Switch. Raise the printer side door. Leave the printhead assembly closed initially. Remove the green plastic lever guard marked “PUSH” by gently prying the back edge with a small flat heat screwdriver. (Fig. 1-1). Using the phillips screwdriver, remove only the middle set screw on top of […]

Sato M84Pro: How to Replace the Printhead

by ScanSource Technical Services November 10, 2010 Barcode Printing
Thumbnail image for Sato M84Pro: How to Replace the Printhead

style=”text-align: left;”>Sato M84Pro Printhead Replacement Switch off the printer and disconnect the power supply cord. Open/remove the top, right, and front housing covers. Remove ribbon and media to provide free access to print head (1, Figure 1-1). Turn thumb screw (2) located on the top side print assembly (3) to release printhead (1). Disconnect the […]

Sato XL410: How to Replace the Printhead

by ScanSource Technical Services November 4, 2010 Barcode Printing
Thumbnail image for Sato XL410: How to Replace the Printhead

Sato XL410 Printhead Replacement Switch the printer off and disconnect the AC Power Cord. Raise the top cover. Remove the center screw holding the head bracket to the thermal head. (Fig. 1-1). Carefully open the printhead so that the printhead will drop down. (Fig. 1-2). Carefully disconnect the printhead data cable and the printhead power […]

Sato M8400RVe: How to Replace the Printhead

by ScanSource Technical Services November 4, 2010 Barcode Printing
Thumbnail image for Sato M8400RVe: How to Replace the Printhead

Sato M8400RVe Printhead Replacement Switch the printer OFF and disconnect the power cable. Open the side access door and raise the top access door. Unload the ribbon and label stock. Close the Head Latch Lever to facilitate removal of the printhead. Remove the center screw. (Fig 1-1) Carefully open the Head Latch Lever so that […]

Printronix SL5000: How To Replace A Printhead

by ScanSource Technical Services October 12, 2010 Barcode Printing
Thumbnail image for Printronix SL5000: How To Replace A Printhead

Replacing the Printhead Printronix T5000/SL5000 WARNING: Always unplug the printer power cord from the printer or power outlet before doing any installation procedure. Failure to remove power could result in injury to you and damage the equipment. When applicable, you will be instructed to apply power. Set the printer power switch to O (Off). Unplug […]