Maintenance

Sato Barcode Label Printers: USB Installation Instructions

by ScanSource Technical Services October 15, 2011 Barcode Printing
Thumbnail image for Sato Barcode Label Printers: USB Installation Instructions

Due to the length and detail of the installation, download and use USB Installation Instructions for SATO Printer. NOTE: The procedure outlined within it must be followed correctly and in the exact order for the installation to be a success. Still have questions or technical trouble? If your already a ScanSource Reseller contact us for [...]

Read More

Zebra QL420 Plus: Adjusting the Power Inactivity Timeout

by ScanSource Technical Services October 15, 2011 Barcode Printing
Thumbnail image for Zebra QL420 Plus: Adjusting the Power Inactivity Timeout

All QL’s come with a default power.inactivity_timeout set to 1200 seconds. (20 minutes). We will adjust it to 0 to keep it from going into sleep mode. However, if you want it set to a different amount of time simply adjust the number in the power.inactivity_timeout.txt file to the desired number of seconds and continue [...]

Read More

Datamax-O’Neil M-Class: Installing the Printhead

by ScanSource Technical Services October 15, 2011 POS
Thumbnail image for Datamax-O’Neil M-Class: Installing the Printhead

Removing the Printhead Turn ‘Off’ and unplug the printer from the AC Receptacle. Open the cover; if ribbon is installed, remove it. With the Printhead locked in the down position, loosen the Printhead Mounting Screw (it will remain in the assembly). Unlatch the Printhead Assembly. While holding the Printhead, raise the assembly. Disconnect the two [...]

Read More

Datamax-O’Neil H-Class: Installing the Peel and Present Option

by ScanSource Technical Services October 12, 2011 Barcode Printing
Thumbnail image for Datamax-O’Neil H-Class: Installing the Peel and Present Option

Installing the Peel and Present option on a Datamax H-Class Printer. Turn ‘Off’ the Power Switch and unplug the power cord from the AC Receptacle. Remove the Thumbscrew and Tear Plate. (Alternately, if equipped with an Arc Plate, Present Sensor, or Cutter, remove that device.) Press the Latch and open the Peel and Present Assembly. [...]

Read More

Datamax-O’Neil H-Class: Installing the Printhead

by ScanSource Technical Services October 12, 2011 Barcode Printing
Thumbnail image for Datamax-O’Neil H-Class: Installing the Printhead

Removing the Printhead Turn OFF the Power Switch and unplug the power cord from the AC Receptacle. With the printhead locked in the down position, loosen the Captivated Screw. (When free, the screw will spring upward). Note: The H-8308 model has two Captivated Screws; loosen both. Unlock the Printhead Latch then raise the Printhead Assembly. [...]

Read More

Datamax-O’Neil H-Class: Printhead Cleaning Procedures

by ScanSource Technical Services October 12, 2011 Barcode Printing
Thumbnail image for Datamax-O’Neil H-Class: Printhead Cleaning Procedures

If print quality declines (symptoms can include unreadable bar codes or streaks through text and graphics), the typical cause is debris buildup on the printhead which, left unattended, can lead to premature dot failure. Depending upon the supplies and printing parameters used, different cleaning methods are recommended. Cotton Swab Procedure (for users of direct thermal [...]

Read More

Datamax-O’Neil H-Class: Installing the Internal Rewind Option

by ScanSource Technical Services October 12, 2011 Barcode Printing
Thumbnail image for Datamax-O’Neil H-Class: Installing the Internal Rewind Option

Kit Contents Turn OFF the Power Switch and unplug the power cord from the AC Receptacle. Remove the Cover Screw and then the Cover Plate. Mount the Rewinder Assembly onto the Center Plate and then secure it using the three Screws. Plug the power cord into the AC Receptacle and turn ON the Power Switch. [...]

Read More

Motorola MC9090: Information on the Heated Boot

by ScanSource Technical Services September 26, 2011 Mobility
Thumbnail image for Motorola MC9090: Information on the Heated Boot

How is it powered? The heated boot for the MC9090G (part # SYM-SGMC902424201R) is powered by 4AA batteries How low is the operating temperature? When used with the MC9090G Condensation model, operating temperature goes down to -22F (-30C) Still have questions or technical trouble? If your already a ScanSource Reseller contact us for further support. [...]

Read More

Sato CL412e: How to Set Up the Enhanced Ethernet Interface

by ScanSource Technical Services August 26, 2011 Barcode Printing
Thumbnail image for Sato CL412e: How to Set Up the Enhanced Ethernet Interface

eSeries Enhanced Ethernet Setup Open Admin Manager and locate printer. Now Double click on the “prninst.exe” icon. Click next to begin the printer installation wizard. Select the printer you would like to install and click next. Enter the printer name and select Add Port. Click Add port then select SATO Port Monitor on LPT, LAN [...]

Read More

Sato CL408e: How to Set Up the Enhanced Ethernet Interface

by ScanSource Technical Services August 26, 2011 Barcode Printing
Thumbnail image for Sato CL408e: How to Set Up the Enhanced Ethernet Interface

eSeries Enhanced Ethernet Setup Open Admin Manager and locate printer. Now Double click on the “prninst.exe” icon. Click next to begin the printer installation wizard. Select the printer you would like to install and click next. Enter the printer name and select Add Port. Click Add port then select SATO Port Monitor on LPT, LAN [...]

Read More

← Previous Entries