Defaults

Zebra 110Xi4: How to Reset Printer to Factory Defaults

by ScanSource Technical Services April 26, 2011 Barcode Printing
Thumbnail image for Zebra 110Xi4:  How to Reset Printer to Factory Defaults

To reset defaults through the front panel, Press two times. The LCD will read SAVE CHANGES. Press until LOAD DEFAULTS is displayed. Press again. The printer will then display LOADING DEFAULTS. Once the printer has reset to default it will perform a self calibration. Still have questions or technical trouble? If your already a ScanSource […]

Zebra R110PAX4: How to Reset Printer to Factory Defaults

by ScanSource Technical Services April 26, 2011 Barcode Printing
Thumbnail image for Zebra R110PAX4:  How to Reset Printer to Factory Defaults

To reset defaults through the front panel, Press two times. The LCD will read SAVE CHANGES. Press until LOAD DEFAULTS is displayed. Press again. The printer will then display LOADING DEFAULTS. Once the printer has reset to default it will perform a self calibration. Still have questions or technical trouble? If your already a ScanSource […]

Zebra ZM600: How to Reset Printer to Factory Defaults

by ScanSource Technical Services April 26, 2011 Barcode Printing
Thumbnail image for Zebra ZM600:  How to Reset Printer to Factory Defaults

To reset defaults through the front panel, Press two times. The LCD will read SAVE CHANGES. Press until LOAD DEFAULTS is displayed. Press again. The printer will then display LOADING DEFAULTS. Once the printer has reset to default it will perform a self calibration. Still have questions or technical trouble? If your already a ScanSource […]

Sato M8400RV: How to Reset Defaults

by ScanSource Technical Services January 18, 2011 Barcode Printing
Thumbnail image for Sato M8400RV: How to Reset Defaults

Sato M8400RV Resetting Defaults Record all current dip switch positions, then place all switches in the OFF position. Place the DSW2-5 in the ON position. Place the printhead in the OPEN position, keeping both the LINE & FEED keys depressed power on the printer. Upon hearing the audible tone, release the LINE & FEED keys. […]

Sato M10e: How to Reset Defaults

by ScanSource Technical Services November 10, 2010 Barcode Printing
Thumbnail image for Sato M10e: How to Reset Defaults

Sato M10e Resetting Defaults Factory settings / Test Print Record all dip switch positions. Place all dip switches in the OFF Position. Place the DSW2-4 in the ON position. Simultaneously, press and hold the LINE and FEED keys while turning on the power switch. Release the LINE and FEED keys upon hearing a beep. Place […]

Sato M8400RVe: How to Reset Defaults

by ScanSource Technical Services November 4, 2010 Barcode Printing
Thumbnail image for Sato M8400RVe: How to Reset Defaults

Sato M8400RVe Resetting Defaults The printer may be reset to use the default software settings by depressing the LINE and FEED keys simultaneously while powering the printer on. You will be asked to confirm that you want the printer default settings by selecting either YES or NO by using the LINE key to step the […]

Cisco AP1260 Access Point: How to Reset Defaults

by ScanSource Technical Services November 3, 2010 Mobility
Thumbnail image for Cisco AP1260 Access Point:  How to Reset Defaults

Applies to APs running IOS only Resetting the Device to Default Settings If you need to start over during the initial setup process, you can reset the access point to factory default settings. Resetting to Default Settings Using the MODE Button/span Follow these steps to reset the access point to factory default settings using the […]

Intermec PX4i: How to Reset Defaults

by ScanSource Technical Services October 25, 2010 Mobility
Thumbnail image for Intermec PX4i: How to Reset Defaults

Intermec PX4i/PX6i Setting Factory Defaults You can reset the PX4i and PX6i to factory defaults using the keypad on the front panel. To reset the printer using the keypad: Turn off the printer. Open the right cover and lift the printhead. Turn on the printer and press and hold the key until the printer beeps. […]

Intermec PX6i: How to Reset Defaults

by ScanSource Technical Services September 11, 2010 Barcode Printing
Thumbnail image for Intermec PX6i: How to Reset Defaults

You can reset the PX6i to factory defaults using the keypad on the front panel. Turn off the printer. Open the right cover and lift the printhead. Turn on the printer and press and hold the key until the printer beeps. Quickly press the following keys in sequence:   The following message appears on the […]